Coin Counter's User's Guide
- Author:Lily Li
- Source:Originality
- Release on :2016-05-20
USER’S GUIDE
FOR ELECTRONIC COIN SORTER
WARNING!
For your safety, it is very important that you always follow the simple
Precautions as below:
- Do not operate the machine if you, or it, are damp. Operating the machine
under wet damp conditions can lead to an electrical shock hazard that
might result in serious injury.
-Use only the same type and rating when replacing a fuse. Using an incorrect Fuse can cause a potential fire hazard if a higher rating Fuse is used.
-Ensure that both the machine and the domestic mains supply system are of the same voltage. An in correct supply voltage could cause a potential fire hazard.
-Turn off and unplug the power before performing maintenance.
-Do not start the machine when the back cover is open.
-Do not put your fingers inside the hopper or channel when the machine is under operation.
-Turn off and unplug the power when long time no using.
-Should you have any doubts, please contact your local distributor, or sales agent, for further advice.
Coin Drawer Fuse(at the bottom)
SPECIFICATION
|
Ambient temperature |
0~40 degC |
|
Ambient Humidity |
30~80% |
|
Hopper capacity |
Max.500units |
|
Each coins drawer |
50~300units |
|
Batch preset number display |
3 Digits LED |
|
Counting number display |
4 Digits LED |
|
Power source |
AC220V/50HZ□ AC110V/60HZ□ |
|
Power consumption |
<45W |
|
Dimensions |
345x306x260(mm) |
|
Net weight |
3.9kg |
|
Counting speed |
Max.270units/min |
**In the interest of our ongoing policy of continual improvement,
specifications are subject to change without prior notice. ***
OPERATION
1.Make sure that the machine is put on level and then turn on the machine.
2.Set an expected batch.
Each channel can be set an expected batch (from 0 to 999).
Press the “SET” key to select the channel, and the “BAT” key, “+” key and “-” key to set the expected batch number.
Note 1: If some channels set the batch to 0, the machine will not stop this channel even the drawer is full, unless the “START/STOP” key is pressed or no coin drop though the channel within 20 seconds.
Note 2: Keep “-” key pressed in 7 seconds can set all the channels to
batch 0.
Note 3:The batch setting can be automatically memorized.
3.Start counting
Put coins in the hopper,and press the “START/STOP”key to start counting.
Press the “START/STOP” again to stop the counting.
4.Check the report
Press the “REPORT” key circularly when the machine in standby state can check the counting results of each channel. Press the “C” key can exit this checking procedure.
MAINTENANCE WARNING!
TURN OFF THE MACHINE AND UNPLUG THE POWER BEFORR THE FOLLOWING MAITANENANCE!
1.Foreign object falls into the hopper will cause jamming or even damage the machine! Please do avoid the foreign object falls in.
As following shown, to remove the foreign object, just open the back Cover and pick out the foreign object.
2.To remove the coin jamming, as following pictures shown, use a finger to push up the jammed coin and let it fall out from the gap between the channels.
3.If the machine is switched on, the electron undergoes a test itself. It may results in one of the following error messages:
EA: Means optical sensor blocked: stop the machine and remove the back cover, then turn the carry tray by your hands, by outer light you see the glass which on top left corner, then clear the dust on the glass. Because there is too much dust on the glass and it affects the optical sensor work.
If the machine often appears EA, it may be due to working environment leading too much dust in the inner of the machine, to clean the inner parts of the machine. a: switch off the machine and cut down power. b: remove 3 bolts on bottom of crust, remove the crust. c: clean dust, end to reset.
E1…E8 Means count sensor blocked.(According to the coin diameter from short to long range)
E9 Means running sensor blocked.
If it takes no effect after cleaning the inner parts as well as sensors, the machine needs repaired.
